300-510 Dumps PDF New [2022] Ultimate Study Guide [Q26-Q43]

4/5 - (3 votes)

300-510 Dumps PDF New [2022] Ultimate Study Guide

300-510 Exam Dumps PDF Updated Dump from PrepAwayTest Guaranteed Success

Prerequisites for Final Exam

The individuals concerned will already have awareness and skills involving how to execute and operate Cisco core technologies for the networks that are targeted at the Service Providers. They should also have a deep comprehension of the 300-510 subject matter so gaining the requisite knowledge takes deliberate learning that makes use of recommended courses as well as revision or study guides. Potential candidates should also be aware of the registration process for the official test. Thus, they should have a Pearson VUE account before they can do the final registration, which includes selecting the number of the evaluation they intend to do.

Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Certification Path

Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) exam is affiliated with the CCNP Service Provider and Cisco Accredited Professional-Service Provider VPN Services Implementation certifications. This is the official prerequisite for this exam. However, the course, Integrating VPN Services from Cisco Service Provider, allows applicants to prepare for this exam and is highly recommended.

NEW QUESTION 26
Refer to the exhibit. Which two commands must the engineer configure for the company’s PIM- PIM network to enable Auto-RP mappings to be sent over the FastEthernet0/0 interface without affecting normal operation? (Choose two)

enable auto-rp listener

enable sparse-dense mode

enable sparse-mode

enable Auto-RP announcements

enable dense mode

NEW QUESTION 27
Refer to the exhibit.

An engineer has configured all routers in the environment to run IS-IS Level 1 and Level 2 routing. The engineer wants traffic from R1 to R5 to pass via R2. but IS-IS routing has calculated the best path via R4.
Which action corrects the problem?

Configure routers R1, R4, and R5 for Level 2 routing only.

Set the link metric for the link from router R1 to router R4 to 30 or more.

Set the link metric on R2 for the links from router R2 to routers R3 and R4 to 30 or more.

Configure routers R1, R2, and R5 for Level 1 routing only.

NEW QUESTION 28
Refer to the exhibit.

An engineer has successfully fixed BGP peering issue. R1 has an established eBGP peering with R2 and R3. Which mechanism should the engineer apply in order to steer the traffic correctly?

The MED attribute can be applied on R2 to influence R1 to use it as the primary path.

The local preference attribute can be applied on R3 to influence AS 65513 to use AS 65515 as the secondary path.

The weight attribute can be applied on R2 to influence AS 65513 to use AS 65515 as the primary path.

The IGP metric can be manipulated on R1 to allow traffic to be load balanced between R2 and R3.

NEW QUESTION 29

Refer to the exhibit. Router 1 is a core ABR in a Cisco Unified MPLS environment. All of the router 1 BGP peers are established, but traffic between customers is failing. Which BGP configuration must be added to the configuration?

It must be configured for graceful restart

It must be configured with a route reflector

It must be configured with send labels

It must be configured with PIC edge

NEW QUESTION 30
Refer to the exhibit. P1 and PE3 Cisco IOS XR routers are directly connected and have this configuration applied.
The BGP session is not coming up.
Assume that there is no IP reachability problem and both routers can open tcp port 179 to each other.
Which action fixes the issue?

Change HMAC-MD5 to HMAC-SHA1-20

Configure the send and accept lifetime under key 1

Change HMAC-MD5 to MD5

Change HMAC-MD5 to HMAC-SHA1-12

NEW QUESTION 31
Refer to the exhibit.

An engineer is addressing an IS-IS design issue which is running within the topology. All links are running on FastEthernet, except the link between R5 and R4, which is Gigabit Ethernet. Which statement about the design is true?

R4 prefer to reach R5 using R1 as the next hop

All links have equal cost if the default metric is used

R5 prefers to use R4 as the next hop for all routes

R1 prefer to use R5 as the next hop to reach R4

NEW QUESTION 32
A network consultant is troubleshooting IS-IS instances to identify why a routing domains is having communication problems between the two instances. Which description of the possible cause of issues in the routing domain is true?

The same interface cannot be advertised in two different IS-IS instances

The IS-IS “ISP” and “ISP2” instances are unrelated and unable to intercommunicate

The configured IS-IS NSEL value is not allowing the routing systems to establish a neighborship

The interface mode ip router is-is command was not included in the script

Reference:
irs-instance-vrf.html

NEW QUESTION 33

Refer to the exhibit. XR1 and XR2 are sending the prefix 10.11.11.0/24 to XR3. A configured policy on XR1 is incorrectly prepending AS path 11 11 12 12 onto this prefix. A network operator wants to add a policy onto XR3 that will not allow the falsely prepending prefix from being installed. Which policy configuration applied to the XR3 neighbor configuration for XR1 can accomplish this requirement without impact to other or future received routes?

Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-1/routing/command/reference/ b_routing_cr41crs/b_routing_cr41crs_chapter_01000.html#wp3850885229

NEW QUESTION 34
A network consultant is troubleshooting IS-IS instances to identify why a routing domains is having communication problems between the two instances.
Which description of the possible cause of issues in the routing domain is true?

The same interface cannot be advertised in two different IS-IS instances

The IS-IS “ISP” and “ISP2” instances are unrelated and unable to intercommunicate

The configured IS-IS NSEL value is not allowing the routing systems to establish a neighborship

The interface mode ip router is-is command was not included in the script

https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_isis/configuration/xe-3s/irs-xe-3s-book/ irs-instance-vrf.html

NEW QUESTION 35
Refer to the exhibit. Why is neighbor 10.1.5.5 stuck in “2WAY” state?

Router ID 10.1.5.5 is not reachable from R2

OSPF authentication has failed between R2 and 10.1.5.5

It is an expected behavior when OSPF network type is broadcast

OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5

https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13683-11.html

NEW QUESTION 36
Refer to the exhibit.

How are packets directed through the data plane when SRv6 is implemented?

An ordered list of segments is encoded in a routing extension header

The MPLS data plane is used to push labels onto IGP routes

A stack of labels represents an ordered list of segments

The packet is encapsulated with a header and trailer encoding the ordered list of segments

NEW QUESTION 37
Refer to the exhibit.

An engineer working for a private telecommunication company with an employee id 3977 74 814 implemented the configuration on Router 1. what is the effect of it?

Router 1 sends and receives multiple best paths from neighbor 192.168.1.1

Router 1 sends up to three paths to neighbor 192.168.1.1 for all routes

Router 1 sends only one best path to neighbor 192 168.1.1.

Router 1 receives only one best path from neighbor 192.168.1.1

NEW QUESTION 38
An engineer is troubleshooting end-to-end customer traffic across an MPLS VPN service provider network.
Which tasks should the engineer use to solve the routing issues? Drag and drop the table types from the left onto the most useful troubleshooting tasks/router types on the right. (Not all options are used.)

NEW QUESTION 39
For which reason can two devices fail to establish an OSPF neighbor relationship?

The two devices have different process IDs

The two devices have different network types

The two devices have different router IDs

The two devices have the same area ID

https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13699-29.html

NEW QUESTION 40
An engineer is troubleshooting slow performance issues on a customer’s network after the last multicast configuration change was applied on it. While checking the running configuration on the router the engineer notices there are many ip igmp join-group commands applied on several interfaces of the router which caused the high CPU utilization usage.
What action must the engineer take to solve this issue?

Configure ip igmp static-group command on all interfaces

Remove ip igmp join-group command on all unnecessary interfaces

Configure all router interfaces to be process-switched by increasing the query interval

Remove unnecessary members from the IGMP group

NEW QUESTION 41
Refer to the exhibit.

Why is neighbor 10.1.5.5 stuck in “2WAY” state?

Router ID 10.1.5.5 is not reachable from R2

OSPF authentication has failed between R2 and 10.1.5.5

It is an expected behavior when OSPF network type is broadcast

OSPF parameters (Area ID or hello interval) are mismatched between R2 and 10.1.5.5

NEW QUESTION 42

Refer to the exhibit. A network operator must stop 10.33.33.33/32 from being redistributed into Level 1 router XR1. Which configuration meets this need?

Explanation/Reference:

NEW QUESTION 43
Refer to the exhibit.

A network operators configuring BGP PIC on CE1 on already established neighborships with PE1ana PE2 inside the fully converged MPLS network Which element needs to be implemented to make this feature function effectively?

Bidirectional Forwarding Detection must be applied to the upstream facing BGP interfaces.

The operator must ensure that all prefixes have the same next-hop from PE1 and PE2 for BGP PICA reserved BGP

community of 1 10 must be used to denote the PIC feature set to the routing protocol

BGP import export policies must be applied on all devices for the routes needing BGP for PIC

Loading …

Pass Your Cisco Exam with 300-510 Exam Dumps: https://www.prepawaytest.com/Cisco/300-510-practice-exam-dumps.html

Prerequisites for Final Exam

Implementing Cisco Service Provider Advanced Routing Solutions (300-510 SPRI) Certification Path

Leave a Reply Cancel reply