[2022] Free 200-301 Exam Dumps to Pass Exam Easily [Q120-Q134]

Rate this post

[2022] Free 200-301 Exam Dumps to Pass Exam Easily

200-301 Exam Dumps, 200-301 Practice Test Questions

NO.120 Which 3 feature are represented by A letter in AAA? (Choose Three)

authorization

accounting

authentication

accountability

accessibility

authority

NO.121 Refer to the exhibit.

Traffic sourced from the loopback0 Interface is trying to connect via ssh to the host at 10.0.1.15. What Is the next hop to the destination address?

192.168.0.7

192.168.0.4

192.168.0.40

192.168.3.5

NO.122 Refer to the exhibit.

What is the effect of this configuration?

The switch port interface trust state becomes untrusted

The switch port remains administratively down until the interface is connected to another switch

Dynamic ARP inspection is disabled because the ARP ACL is missing

The switch port remains down until it is configured to trust or untrust incoming packets

NO.123 Refer to the exhibit An engineer must configure GigabitEthemet1/1 to accommodate voice and data traffic. Which configuration accomplishes this task?

Option A

Option B

Option C

Option D

NO.124 Using direct sequence spread spectrum, which three 2.4-GHz channels are used to limit collisions?

1,6.11

1,5,10

1,2,3

5,6,7

NO.125 Refer to the exhibit.

The network administrator wants VLAN 67 traffic to be untagged between Switch 1 and Switch 2 while all other VLANs are to remain tagged.
Which command accomplishes this task?

switchport access vlan 67

switchport trunk allowed vlan 67

switchport private-vlan association host 67

switchport trunk native vlan 67

NO.126 A port security violation has occurred on a switch port due to the maximum MAC address count being exceeded Which command must be configured to increment the security-violation count and forward an SNMP trap?

switchport port-security violation access

switchport port-security violation protect

switchport port-security violation restrict

switchport port-security violation shutdown

https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/25ew/configuration/guide/conf/port_sec.html

NO.127 Refer to the exhibit.

Given the output from the show ip eigrp topology command, which router is the feasible successor?

10.1.0.1 (Serial0), from 10.1.0.1, Send flag is 0x0 Composite metric is (46152000/41640000), Route is Internal Vector metric: Minimum bandwidth is 64 Kbit Total delay is 45000 Microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2

10.0.0.2 (Serial0.1), from 10.0.0.2, Send flag is 0x0 Composite metric is (53973248/128256), Route is Internal Vector Metric: Minimum bandwidth is 48 Kbit Total delay is 25000 Microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 1

10.1.0.3 (Serial0), from 10.1.0.3, Send flag is 0x0 Composite metric is (46866176/46354176), Route is Internal Vector metric: Minimum bandwidth is 56 Kbit Total delay is 45000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2

10.1.1.1 (Serial0.1), from 10.1.1.1, Send flag is 0x0 Composite metric is (46763776/46251776), Route is External Vector metric: Minimum bandwidth is 56 Kbit Total delay is 41000 microseconds Reliability is 255/255 Load is 1/255 Minimum MTU is 1500 Hop count is 2

NO.128 Refer to the exhibit.

If OSPF is running on this network, how does Router 2 handle traffic from Site B to 10.10.13/25 at Site A?

It load-balances traffic out of Fa0/1 and Fa0/2

It sends packets out of interface Fa0/2 only.

It sends packets out of interface Fa0/1 only.

It cannot send packets to 10.10.13 128/25

Router2 does not have an entry for the subnet 10.10.13.128/25. It only has an entry for 10.10.13.0/25, which ranges from 10.10.13.0 to 10.10.13.127.
https://study-ccna.com/administrative-distance-metric/

NO.129 Refer to the exhibit.

An extended ACL has been configured configuration failed to work as
intended Which two
changes stop outbound traffic on TCP the 10.0.10 0/26 subnet while
still allowing all other traffic? (Choose
two )

Add a “permit ip any any” statement to the begining of ACL 101 for allowed traffic.

Add a “permit ip any any” statement at the end of ACL 101 for allowed traffic

The source and destination IPs must be swapped in ACL 101

The ACL must be configured the Gi0/2 interface inbound on R1

The ACL must be moved to the Gi0/1 interface outbound on R2

NO.130 Drag and drop the SNMP manager and agent identifier commands from the left onto the functions on the right

Explanation

NO.131 Which protocol sends authentication and accounting in different requests?

RADIUS

TACACS+

EAP-Chaining

PEAP

EAP-TLS

NO.132 Which result occurs when PortFast is enabled on an interface that is connected to another switch?

Spanning tree may fail to detect a switching loop in the network that causes broadcast storms

VTP is allowed to propagate VLAN configuration information from switch to switch automatically.

Root port choice and spanning tree recalculation are accelerated when a switch link goes down

After spanning tree converges PortFast shuts down any port that receives BPDUs.
Enabling the PortFast feature causes a switch or a trunk port to enter the STP forwarding-state immediately or upon a linkup event, thus bypassing the listening and learning states.
Note: To enable portfast on a trunk port you need the trunk keyword “spanning-tree portfast trunk

NO.133 Drag and drop the characteristics of network architectures from the left onto the type of architecture on the right.