New 2022 HPE6-A47 Dumps for HP ACDP Certified Exam Questions & Answer [Q41-Q63]

4/5 - (5 votes)

New 2022 HPE6-A47 Dumps for HP ACDP Certified Exam Questions and Answer

Realistic Verified HPE6-A47 exam dumps Q&As – HPE6-A47 Free Update

HP HPE6-A47 Exam Syllabus Topics:

Topic	Details
Topic 1	Select the wired and wireless networking technologies for the design select components based on the analysis results
Topic 2	Plan and design an Aruba solution per the customer requirements for a single-site campus environment with less than 1000 employees or subsystems of an enterprise-wide network.
Topic 3	Given a scenario, select the appropriate products based on the customer technical requirements
Topic 4	Given the customer’s requirements, explain and justify the recommended solution design and document the logical and physical network solutions
Topic 5	Given the customer requirements, determine the component details and document the high-level design choose the appropriate components that should be included on the BOM
Topic 6	Given a scenario, evaluate the customer requirements to identify gaps per a gap analysis Given the customer requirements, design the high-level architecture
Topic 7	Given a customer scenario, explain how a specific technology or solution would meet the customer requirements
Topic 8	Evaluate the requirements for a single-site campus environment with less than 1000 employees or subsystems of an enterprise-wide network
Topic 9	Given a customer scenario, determine and document a detailed network management design design and document a detailed network security solution

NEW QUESTION 41
Refer to the exhibit.

The customer requires fast failover if any one link or core device fails. Which additional technology should the architect plan on the core VSF fabric to meet these criteria?

OSPF graceful restart

SmartLink

BGP

VRRP

NEW QUESTION 42
Refer to the exhibit.

The exhibit shows the current plan for a wired network upgrade.
As much as possible, the customer wants to flatten the architecture and avoid recabling. However, each Building 2 switch must also maintain connectivity to the core if one link fails. What should the architect propose to meet the customer requirements?

Use two additional 2930F switches to act as an aggregation layer for Building 2; connect them to the core on 40 GbE connections.

Connect each Building 2 switch directly to the core on a single fiber strand through the use of SFP+-SR transceivers.

Combine the switches in each Building 2 closet as a VSF fabric; establish two 10 GbE connections to the core per fabric.

Extend additional fiber between the buildings so that each Building 2 switch can have a direct 10 GbE connection to the core.

NEW QUESTION 43
What typically drives the need for an aggregation layer in modern networks?

insufficient fiber cabling, especially between buildings

lack of high speed uplink capabilities at the access layer

simplification of spanning tree protocol ad the access layer

need to extend VLANs across wider areas

NEW QUESTION 44
Refer to the exhibit.

The customer needs to expand its wired and wireless network to a new building, Building 2, which is near the
existing building, Building 1. The exhibit shows the logical plan that the architect has created so far. The
aggregation layer switches in the new building should provide the default gateway services for the VLANs in
the new building and route traffic to the core. The existing Aruba Mobility Controllers (MCs) will control the
new APs.
What should be the VLAN assignment for Link 1, indicated in the exhibit?

an unused VLAN such as 200

VLANs 21, 22, and 23 only

VLANs 11, 12, 13, 21, 22, and 23

the default VLAN and VLAN 14

NEW QUESTION 45
What is a key criteria that an architect should use to choose between an Aruba 7000 Series or 7200 Series Mobility Controller (MC)?

the number of wireless devices that the MC needs to support

whether the MC needs to terminate VPN tunnels

the need to deploy controllers in a cluster

whether the MC needs to support advanced 8.x features

NEW QUESTION 46
A customer needs a wireless solution upgrade. Among the devices that need wireless access are printers.
What information about the printers does the architect need to plan the wireless solution? (Select two.)

whether the printers are physically locked down

the identify of users who need to access printers

whether the printers support Power over Ethernet (PoE)

whether the printers support 802.1X

the 802.11 standards supported by the printer

NEW QUESTION 47
A customer currently has an Instant AP deployment. Which customer requirement would indicate that the customer needs to add a controller to the deployment?

the requirement to apply role-based firewall policies

the requirement for a captive portal for guests

the requirement to provide client-to-site VPN acces for remote users

the requirement for a cloud-based management solution

NEW QUESTION 48
A customer requires APs that meet these minimal criteria:
1. Support for MU-MIMO
2. Support for up to four spatial streams, both when MU-MIMO is used and when it is not used
3. Support for transmissions to up to three MU-MIMO clients at the same time The architect finds these specifications for the two models under consideration:
AP-335 = 4×4:4:4:4:3
AP-325 = 4×4:4:4:3:3
What should the architect determine from these specifications?

The AP 335 and the AP 325 do not meet the customer requirements, so consider a different model.

The AP 325 meets the customer requirements, but the AP 335 does not.

Either the AP 335 or the AP 325 meet the customer requirements.

The AP 335 meets the customer requirements, but the AP 325 does not.

NEW QUESTION 49
A customer currently has an Instant AP deployment. Which customer requirement would indicate that the customer needs to add a controller to the deployment?

the requirement to apply role-based firewall policies

the requirement for a captive portal for guests

the requirement to provide client-to-site VPN access for remote users

the requirement for a cloud-based management solution

NEW QUESTION 50
An architect proposes an Aruba solution with a hardware Mobility Master (MM) to a customer. The customer has a disaster recovery site which is connected to the main site at Layer 3. The customer requires the MM to remain available in case of a total site failure.
Which plan meets the customer requirements?

Deploy a hardware MM to the disaster recovery site and set up VRRP between them.

Deploy a hardware MM to the disaster recovery site and set its IP address as the standby master for MCs.

Deploy the virtual MM (VMM) to the disaster recovery site and set the VMM IP address to the same address as the hardware MM.

Deploy the virtual MM (VMM) to the disaster recovery site and configure clustering on the hardware and software appliances.

NEW QUESTION 51
An architect plans to purpose two Aruba Mobility Controllers (MCs) in a cluster. The customer has a large building that needs to support about 10,000 devices. The architect plans to associate the Employees WLAN with VLAN ID 10.
What is one Aruba best practice for this design?

Ensure that VLAN 10 is extended to the edge and Aruba APs are deployed on it.

Ensure that each user role on the MCs is associated with a different VLAN ID.

Ensure that the RADIUS server assigns users to different VLANs dynamically.

Ensure that optimization and suppression of unnecessary multicast is enabled.

NEW QUESTION 52
Refer to the exhibit.

The exhibit shows information about a customer’s existing equipment in a closet. The customer needs an upgrade for this closet.
The architect plans to:
* Replace the switches with two Aruba 3810M switches
* Connect the 3810M switches in a backplane stack
* Upgrade the uplinks to two 40GbE links for the entire backplane stack What is required for this design?

Upgrade the fiber to single mode or a higher grade multimode.

Use QSFP BiDi transceivers for the 40 GbE uplinks.

Use QSFP SR4 transceivers for the stacking connections.

Deploy more MM OM2 strands to make a total of 24.

NEW QUESTION 53
Refer to the exhibit.

The customer needs to expand its wired and wireless network to a new building, Building 2, which is near the existing building, Building 1. The exhibit shows the logical plan that the architect has created so far. The aggregation layer switches in the new building should provide the default gateway services for the VLANs in the new building and route traffic to the core. The existing Aruba Mobility Controllers (MCs) will control the new APs.
What should be the VLAN assignment for Link 1, indicated in the exhibit?

an unused VLAN such as 200

VLANs 21, 22, and 23 only

VLANs 11, 12, 13, 21, 22, and 23

the default VLAN and VLAN 14

NEW QUESTION 54
A customer requires a wireless upgrade. The architect proposes:
* Aruba AP-325s
* Mobility Controller (MC) 7210s
* Virtual Mobility Masters (MMs)
* ClearPass
* AirWave
The customer is interested in wired authentication, as well as wireless authentication, but does not have the
budget to upgrade the wired network. The wired network does not currently support 802.1X or RADIUS.
Which feature of the Aruba solution should the architect explain to justify the proposed solution?

The customer can direct all wired traffic through the MCs, which will then apply security to that traffic.

The customer can direct all wired traffic through the MMs, which will impose basic security checks.

ClearPass OnConnect can enable wired authentication on these switches through the use of SNMP.

AirWave can manage these switches and shut down their ports if an unknown user or device connects.

NEW QUESTION 55
Refer to the exhibit.

A customer wants to replace the core and aggregation layer of an existing network. Currently the network routes between the aggregation layer and core, and uses the technologies shown in the exhibit.
The customer now wants to route at the core, instead of the aggregation layer, and extend some of the same VLANs in different buildings. However, the customer cannot eliminate the aggregation layer at this point. What should the architect recommend?

Create a backplane stack at the aggregation layer and a VSF fabric at the core.

Implement broadcast filtering on switch-to-switch links across all of the buildings.

Combine all switches in the aggregation layer and core into a single backplane stack.

Use VRRP on the core and aggregation switches, with the aggregation switches acting as standby.

NEW QUESTION 56
A customer has several clusters of Aruba 325 Instant APs. The customer is happy with the performance of the
current APs, but would like to add a Mobility Controller (MC). What should the architect propose?

the purchase of Universal APs that are the same modes as the current APs.

Aruba ClearPass to onboard the APs as campus APs in the new MC-based deployment

conversion of the existing Instant APs to campus APs (CAPs)

a Virtual Mobility Controller (VMC) which can be licensed to control Instant APs

NEW QUESTION 57
Refer to the exhibit.

An architect selects 5406R switches for the aggregation layer. What is an appropriate amount of bandwidth for the link aggregation between each aggregation layer VSF fabric and the campus core?

60 Gbps

160 Gbps

200 Gbps

320 Gbps

NEW QUESTION 58
Refer to the exhibit.

The exhibit shows the current plan for a wired network upgrade.
As much as possible, the customer wants to flatten the architecture and avoid recabling. However, each Building 2 switch must also maintain connectivity to the core if one link fails. What should the architect propose to meet the customer requirements?

Use two additional 2930F switches to act as an aggregation layer for Building 2; connect them to the core on 40 GbE connections.

Connect each Building 2 switch directly to the core on a single fiber strand through the use of SFP+-SR transceivers.

Combine the switches in each Building 2 closet as a VSF fabric; establish two 10 GbE connections to the core per fabric.

Extend additional fiber between the buildings so that each Building 2 switch can have a direct 10 GbE connection to the core.

NEW QUESTION 59
A customer needs a networking solution that supports their Microsoft Skype for Business Unified Communications (UC) solution. The architect discovers that user wireless devices are Wi-Fi Multimedia (WMM) capable. Windows policies assign voice traffic DSCP 46 and video traffic DSCP 34.
Which potential issue should the architect explain to the customer about the default QoS settings?

The DSCP values place both voice and video traffic in the video VMM queue, so voice does not receive the prioritization that is should.

The Aruba APs and controllers use different prioritization mechanism from WMM, so they will not accept high priority traffic from the wireless devices.

DSCP is incompatible with WMM. The Aruba APs and controllers instead use 802.1p to mark traffic to and from wireless devices.

The DSCP for wireless client traffic is concealed within the GRE packet on the path from the AP to the controller, and does not take effect.

NEW QUESTION 60
Refer to the exhibit.

An architect selects 5406R switches for the aggregation layer. What is an appropriate amount of bandwidth for the link aggregation between each aggregation layer VSF fabric and the campus core?

60 Gbps

160 Gbps

200 Gbps

320 Gbps

NEW QUESTION 61
Refer to the exhibit.

The customer requires fast failover if any one link or core device fails. Which additional technology should the architect plan on the core VSF fabric to meet these criteria?

OSPF graceful restart

SmartLink

BGP

VRRP

NEW QUESTION 62
An architect plans to purpose two Aruba Mobility Controllers (MCs) in a cluster. The customer has a large
building that needs to support about 10,000 devices. The architect plans to associate the Employees WLAN
with VLAN ID 10.
What is one Aruba best practice for this design?

Ensure that VLAN 10 is extended to the edge and Aruba APs are deployed on it.

Ensure that each user role on the MCs is associated with a different VLAN ID.

Ensure that the RADIUS server assigns users to different VLANs dynamically.

Ensure that optimization and suppression of unnecessary multicast is enabled.

NEW QUESTION 63
Refer to the exhibit.

An architect determines that 80 Gbps bandwidth is required for the link aggregation between the Building
1aggregation layer and Building 2. Which transceivers should the architect recommend for each pair of switches?

two QSPF+ BiDi

two QSPF+ MPO

eight SPF+ LR

eight SFP+ SR

Use Real HPE6-A47 Dumps – 100% Free HPE6-A47 Exam Dumps: https://www.prepawaytest.com/HP/HPE6-A47-practice-exam-dumps.html

HP HPE6-A47 Exam Syllabus Topics:

Leave a Reply Cancel reply