Free Juniper JN0-363 Study Guides Exam Questions & Answer [Q108-Q126]

Rate this post

Free Juniper JN0-363 Study Guides Exam Questions and Answer

JN0-363 Exam Dumps, JN0-363 Practice Test Questions

NEW QUESTION 108
Which three attributes are well-known mandatory BGP attributes? (Choose three.)

next-hop

AS path

local preference

MED

origin

NEW QUESTION 109
Which statement is true about the operation of Layer 2 VPNs?

Layer 2 VPNs require that CE devices use the same Layer 2 encapsulation

Layer 2 VPNs do not permit CE devices to operate a Layer 3 protocol with each other

Service provider routers must evaluate the IP header of packets as they traverse their network

Layer 2 VPNs allow CEs to use different encapsulations on either side of the VPN

NEW QUESTION 110
Which two statements are correct regarding VPLS mesh groups? (Choose two.)

Unicast packets destined to another PE router within the same mesh group are dropped by the local PE router.

Unicast packets destined to another PE router in a different mesh group are dropped by the local PE router.

Broadcast, multicast, and unicast packets of unknown origin received from a PE router are flooded to all local CE routers.

Broadcast, multicast, and unicast packets of unknown origin received from a PE router are flooded to all remote PE routers.

NEW QUESTION 111
Click the Exhibit.

Referring to the exhibit, which IS-IS router will be selected as the DIS?

Router 1

Router 4

Router 2

Router 3

NEW QUESTION 112
Click the Exhibit button.

You must create a static route on Router-A to the 10.10.5.0/24 network using 10.10.3.2 as the next hop.
Referring to the exhibit, which configuration accomplishes this task?

NEW QUESTION 113
By default, which RSVP reservation style is used by the Junos OS?

fixed explicit

fixed filter

shared explicit

wildcard filter

NEW QUESTION 114
You are advertising a summary route that represents your local network (172.20.0.0716) to both ISP A and ISPB. You want to influence all traffic sent to you from ISP C to go through R2.
How would you accomplish this task?

On R1, prepend your AS number three times on the 172.20.0.0/16 route when advertising It to ISP 1.

On R1, change the local preference value to 250.

On R2. prepend your AS number three times on the 172.20.0.0/16 route when advertising it to ISP 2.

On R2, change the local preference value to 50.

NEW QUESTION 115
Click the Exhibit button.

Referring to the exhibit what are two reasons for the configuration stanza? (Choose two.)

to reduce the risk of forwarding traffic through a stateless tunnel

to mark the tunnel down after the hold-time expires

to remove the tunnel interface from inet.0 after the hold-time expires

to mark the tunnel up after the hold-time expires

NEW QUESTION 116
Click the Exhibit button.

You configured R1 and R2 to form an OSPF adjacency, but the adjacency will not establish.
Referring to the exhibit, which statement correctly identifies the problem?

Hello and dead timers are not matching between R1 and R2

R1 does not have a router ID defined

R1 and R2 have the same router ID

R2 has a wrong area configured

NEW QUESTION 117
Which two statements ate correct about the BGP next-hop attribute value? (Choose two.)

By default, the next-hop value is changed across IBGP links.

By default, the next-hop value is changed across EBGP links.

By default, the next-hop value is not changed across IBGP links.

By default, the next-hop value is not changed across EBGP links.

NEW QUESTION 118
Which two routing protocols make use of a designated router, or pseudo node, to represent a broadcast network? (Choose two.)

BGP

OSPF

MPLS

IS-IS

NEW QUESTION 119
You notice that the RID of your router is being taken from the address of your management interface.
What could cause this scenario?

The loopback address was configured with a /32 address.

The loopback address was not configured under [edit protocols ospf].

A suitable loopback address was not configured on the router.

The loopback address was configured under [edit routing-options].

NEW QUESTION 120
In which situation would you disable penultimate-hop popping?

When you want to bypass a penultimate router that does not support IPv6 tunneling

When you want to ensure the penultimate router can perform the destination route lookup

When you want to enforce the same class-of-service behavior through the entire LSP

When you want to utilize a penultimate router that supports IPv6 tunneling

NEW QUESTION 121
Exhibit

Which two statements ate correct about the actions taken as the packet traverses the service provider MPLS network from Site 1 to Site 2 as shown in the exhibit? (Choose two.)

R2 will perform a lookup using the mpls.0 table.

R1 will perform a lookup using the lnet.3 table.

R1 will perform a lookup using the mpls.0 table.

R2 will perform a lookup using the inet.3 table.

NEW QUESTION 122
Which two statements are correct regarding TLVs in IS-IS? (Choose two.)

PDUs contain different TLVs.

TLVs contain different PDUs.

The TLV attributes are type, length, and value.

The TLV attributes are time. Length, and variable.

NEW QUESTION 123
You are using RSVP to signal an MPLS LSP.
Which statement is true in this scenario?

A secondary path must be configured to establish an LSP.

LSPs can be configured without any traffic engineering constraints.

The traffic engineering database must be used for all LSPs.

A primary path must be configured to establish an LSP.

NEW QUESTION 124
You are asked to configure the OSPF environment to prevent the DR other routers from participating in DR/BDR election.
Referring to the exhibit, which command will accomplish this task?

set protocols ospf area 0.0.0.0 interface ge-0/0/l priority 255

set protocols ospf area 0.0.0.0 interface ge-0/0/1 priority 0

set protocols ospf area 0.0.0.0 interface ge-0/0/1 interface-type nbma

set protocols ospf area 0.0.0.0 interface ge–0/0/1 interface-type p2p

NEW QUESTION 125
You are deploying link aggregation groups.

By default, what are two considerations in this scenario? (Choose two.)

There should only be four member links per LAG.

All the ports must have the same speed.

Member links are required to be contiguous ports.

Member links can reside on different members within an MC-LAG.

NEW QUESTION 126
You have configured multiple IP-IP tunnels across your network to provide connectivity to remote sites.Which technique is used to help the IP endpoints in your network determine the optimal packet size to send across your tunnels?

path MTU discovery

fragmentation discovery

end-to-end MTU discovery

packet throughput discovery

Latest JN0-363 Actual Free Exam Questions Updated 265 Questions: https://www.prepawaytest.com/Juniper/JN0-363-practice-exam-dumps.html

Leave a Reply Cancel reply