2023 Valid NS0-184 test answers & Network Appliance Exam PDF [Q36-Q57]

QUESTION 36
What are two ONTAP storage efficiency technologies that would be used on an AFF A400 cluster? (Choose two.)

QUESTION 37
Click the Exhibit button.

You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?

QUESTION 38
You have just racked a new 6-node switched cluster with ONTAP 9.7. You need to configure the cluster switches.
In this scenario, which two elements would be used to complete the configuration? (Choose two.)

QUESTION 39
You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.
In this scenario, which cluster configuration is allowed with ASA controllers?

QUESTION 40
You are expanding an existing cluster that uses BES-53248 cluster interconnect switches. You connected the new controllers to ports 0/17 through 0/20. However, you are unable to join the new nodes to the cluster.
Which action must be taken to solve the problem?

QUESTION 41
While installing a new AFF A400 HA pair, you are unable to add an NTP server from another subnet. You are able to ping the NTP server from the new cluster.
In this scenario, what are two causes of this problem? (Choose two.)

QUESTION 42
You installed a new pair of Cisco 92300YC cluster switches at a customer’s site. Before you install any files on the switch, you want to view the current configuration.
In this scenario, which command would you use to accomplish this task?

QUESTION 43
After the successful installation of a NetApp ONTAP cluster, the customer wants to know how to view telemetry dat
a. The customer also wants to receive online information about any risks with the cluster and potential best-practice gaps.
Which tool satisfies the customer’s requirements?

QUESTION 44
Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.
In this scenario, which two methods would be supported to migrate the data? (Choose two.)

QUESTION 45
You are installing a new ONTAP 9.7 cluster and attaching the cluster to two separate networks. Your customer has indicated that the same range of client IP addresses are used on both networks and that the networks are never allowed to communicate with each other.
In this scenario, which ONTAP feature must be configured to securely allow all clients to access ONTAP NAS protocols?

QUESTION 46
While testing a recently installed FAS8700 cluster, a node fails. You now need to replace the impaired node.
In this scenario, which two statements are true? (Choose two.)

QUESTION 47
Click the Exhibit button.

During an ONTAP cluster handover procedure, your customer asks how to identify and solve issues that might occur on the newly deployed array.
Referring to the exhibit, which two widgets would the customer use to help with these issues? (Choose two.)

QUESTION 48
You have installed a new 2-node FAS9000 cluster with two external shelves. You want to make sure that each node has two paths to each disk in the shelves.
How do you verify your configuration?

QUESTION 49
You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.
Which action must be performed to ensure that the customer’s requests are satisfied?

QUESTION 50
Click the Exhibit button.

You are installing a 2-node AFF A400 switchless cluster. You have cabled the management network to the e0M port. NetApp also recommends cabling to a redundant management network switch.
Referring to the exhibit, to which port should the redundant management network be cabled?

QUESTION 51
When you install a new ONTAP 9.7 4-node cluster, which network type is required?

QUESTION 52
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)

QUESTION 53
You are installing a 4-node AFF A400 cluster and are asked to create a custom security message before and after user login.
Which two security features are used to perform this task? (Choose two.)

QUESTION 54
You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were automatically discovered by “automatic port placement”.
In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)

QUESTION 55
You have just finished installing and configuring an ONTAP cluster for a customer.
In this scenario, which product collects information and produces site documentation?

QUESTION 56
You are installing a new AFF A400 cluster that is running ONTAP 9.7 software. You are asked to attach an Amazon S3 cloud tier for FabricPool technology.
In this scenario, which two NetApp License File (NLF) types are supported for cloud tiering? (Choose two.)

QUESTION 57
You are preparing for the installation of a new 2-node cluster with ONTAP 9.7 using NL-SAS drives. Your customer wants to use the cluster exclusively with FlexGroups.
In this scenario, which two statements are correct? (Choose two.)