Provide Valid 300-425 Dumps To Help You Prepare For Designing Cisco Enterprise Wireless Networks Exam Jul 19, 2024 [Q16-Q31]

Rate this post

Provide Valid 300-425 Dumps To Help You Prepare For Designing Cisco Enterprise Wireless Networks Exam Jul 19, 2024

Cisco 300-425 Dumps Questions [2024] Pass for 300-425 Exam

Cisco 300-425 exam is an integral part of the Cisco Certified Design Expert (CCDE) track. The CCDE certification is a highly respected credential in the IT industry, and passing the 300-425 exam is one of the requirements to earn this certification. 300-425 exam is a challenging test of knowledge and skills, and it requires a deep understanding of wireless networking concepts and technologies.

NEW QUESTION 16
A customer has a Cisco wireless network that supports VoWLAN services. The customer wants supported voice clients to receive roaming recommendations and suggestions from APs. This functionality must not impact non-VoWLAN clients. What should be enabled on the VoWLAN SSID?

802.11r Fast Transition

802.11k neighbor lists

CCKM with 802.1X

802.11v BSS Transition Management

NEW QUESTION 17
A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)

The coverage area must have a noise floor that does not exceed -87 dBm.

The client device must have at least an -67 dBm RSSI.

The rate of retransmitted packets must be 15 percent or below.

The rate of retransmitted packets must be 20 percent or below.

The client device must have at least an -65 dBm RSSI.

NEW QUESTION 18
An engineer is designing a new wireless network. The network needs to fulfill the following requirements:
support multimedia applications
support a high concentration of wireless clients
support data over wireless
support roaming
Which approach should be used?

use of micro cells with reduced power levels

use of macro cells with reduced power levels

coverage for cells at maximum power levels

use of macro cells with maximum power levels

Micro cells with reduced power levels are suitable for environments with a high concentration of wireless clients and multimedia applications, as they help manage interference and allow for better roaming capabilities. References: ENWLSD 300-425 Official Cert Guide.

NEW QUESTION 19
An engineer changed me TPC Power Threshold for a wireless deployment from the default value to -65 dBm The engineer conducts a new post deployment survey to validate the results What is the expected outcome?

increased received sensitivity

decreased channel overlap

decreased client signal strength

increased cell size

NEW QUESTION 20
What is the recommended cell overlap when designing a wireless network for Cisco Hyperlocation?

20%

30%

40%

50%

Cisco Hyperlocation requires a high degree of accuracy in client location tracking. A recommended cell overlap of 50% ensures that client devices are consistently within the range of multiple access points, which improves location accuracy and reliability. References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide.

NEW QUESTION 21
A high-density wireless network is designed. Which Cisco WLC configuration setting must be incorporated in the design to encourage clients to use the 5 GHz spectrum?

RRM

Cisco centralized key management

Band select

Load balancing

Band Select is a feature on Cisco WLCs that encourages dual-band capable clients to connect to the less congested 5 GHz spectrum. It works by delaying the response to clients’ probes on the 2.4 GHz band, making the 5 GHz band more attractive to the client devices.

NEW QUESTION 22
A medium-sized hospitality company with 50 hotels needs to upgrade the existing WLAN m each hotel to 802Hn During the site surveys tor each hotel, what needs to be taken into consideration when determining the locations for each AP?

Selecting AP locations where power is already available

Selecting APs that can be hidden in ceiling panels lo provide a secure and clean aesthetic look.

Selecting locations that make visual assessment of the AP operation easy

Selecting locations that are easily accessed so maintenance and upgrades can be performed quickly

NEW QUESTION 23
A customer asks an engineer to explain the concept of mobility domains and mobility groups. Which statement does the engineer respond with?

A mobility group does not constrain the distribution of security context of a client and also does not constrain AP fail-over between controllers when the WLC are in the same mobility domain.

If WLCs are in the same mobility domain, they communicate with each other but, if an anchor WLC is present it must be in the same mobility domain for communication to be possible.

If WLCs are in the same mobility domain, they communicate with each other. Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.

WLCs do not need to be in the same mobility domain to communicate with each other. Mobility groups constrain the distribution of security context of a client and also constrain AP fail-over between controllers.

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-0/configuration-guide/b_cg80/b_cg80_chapter_010011.html

NEW QUESTION 24
An engineer must decide the cell overlap for a wireless voice deployment. Which Cisco measurement recommendation should be considered?

The edge of the cell should be -67 dBm.

The edge of the cell should be below 35 RSSI.

The measurement should be done on the 2.4-GHz band.

One AP should be deployed per 3000 square feet.

For a wireless voice deployment, Cisco recommends that the edge of the cell should have a signal strength of
-67 dBm to ensure reliable voice quality and seamless roaming capabilities.

NEW QUESTION 25
Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?

rping

ping

eping

mping

NEW QUESTION 26
What causes the most signal attenuation, based on the wireless design tools?

cinder block wall

metal door

glass wall

office window

Metal doors cause the most signal attenuation in wireless design due to the properties of metal reflecting and absorbing radio waves, which can significantly reduce signal strength. Unlike materials such as cinder block or glass, metal can create a complete barrier for the signal, leading to a phenomenon known as “Faraday Cage” effect, where the metallic enclosure blocks electromagnetic fields. References: Designing Cisco Enterprise Wireless Networks (ENWLSD 300-425)

NEW QUESTION 27
An engineer has successfully configured high availability and SSO using two Cisco 5508 Wireless LAN Controllers. The engineer can access the Active Primary WLC, but the Secondary Standby WLC is not accessible. Which two methods allow access to the standby unit? (Choose two.)

via the console connection

SSH to the redundancy management interface of the primary WLC

SSH to the service port interface

SSH to the virtual interface of the secondary WLC

SSH to the management interface of the primary WLC

In a high availability setup with Cisco 5508 Wireless LAN Controllers, the standby controller can be accessed via the console connection and the service port interface. The console provides direct access, while the service port interface allows for network-based access to the standby unit for management purposes.

NEW QUESTION 28
An enterprise has moved most services to the cloud, including email applications and real-time communication. Which feature must be enabled on the wireless network to improve the user experience?

QoS

Radio management

Interference mitigation

Fast secure roaming

Quality of Service (QoS) is essential for prioritizing cloud services like email and real-time communication. It helps in managing bandwidth allocation and ensuring that critical applications receive the necessary resources for optimal performance.
https://community.cisco.com/t5/wireless-mobility-documents/what-is-cckm-and-how-does-it-affect-fast-and-secu

NEW QUESTION 29
Why is 802.11a connectivity reduced in an X-ray room?

X-rays create significant non-Wi-Fi interference on the 802.11a band.

X-rays impact the 802,11a UNll-2 channels that cause access points to dynamically change channels.

X -rays within these rooms cause multipath issues.

X-ray rooms exhibit increased signal attenuation.

portable X-ray machines, sending high-resolution images, sometimes in real time, echography machines, and electrocardiography [ECG] machines). These devices may also use the same spectrum as Wi-Fi but with other protocols and, therefore, become sources of interference for your system.

NEW QUESTION 30
Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)

PoE battery

spirit level

access point

tall tripod

goggles

ladder

Section: Wireless Site Survey

NEW QUESTION 31
Clustering Cisco WLCs into a single RF group enables the RRM algorithms to scale beyond the capabilities of a single Cisco WLC. How many WLC and APs in an RF group can the controller software scale up to in WLC release 8.9 depending on the platform?

up to 20 WLCs and 1000 APs

up to 20 WLCs and 3000 APs

up to 20 WLCs and 4000 APs

up to 20 WLCs and 6000 APs

https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-9/config-guide/b_cg89/radio_resource_management.html

Loading …

Cisco 300-425 exam is one of the most popular exams in the Cisco certification program. 300-425 exam is designed to test the candidate’s knowledge of wireless networking technologies, including designing, deploying, and troubleshooting wireless networks. 300-425 exam covers topics such as WLAN high availability, advanced location services, and multicast services. 300-425 exam is designed to validate the skills of professionals who are involved in the design and implementation of wireless networks.

Achieve Success in Actual 300-425 Exam 300-425 Exam Dumps: https://www.prepawaytest.com/Cisco/300-425-practice-exam-dumps.html

Leave a Reply Cancel reply