[2026] New NSE7_SDW-7.2 exam Free Sample Questions to Practice [Q55-Q79]

Rate this post

[2026] New NSE7_SDW-7.2 exam Free Sample Questions to Practice

Cover Real NSE7_SDW-7.2 Exam Questions Make Sure You 100% Pass

Fortinet NSE7_SDW-7.2 Exam Syllabus Topics:

Topic	Details
Topic 1	Rules and Routing: Understanding SD-WAN Rules and Routing is crucial for directing traffic effectively. This topic of the NSE7_SDW-7.2 exam evaluates the capabilities of Fortinet network and security professionals to configure SD-WAN rules and routing.
Topic 2	SD-WAN Configuration: This topic assesses skills of Fortinet network and security professionals in setting up basic SD-WAN environments, including configuring Direct Internet Access (DIA), SD-WAN Members, and Performance Service Level Agreements (SLAs). Proficiency here ensures the ability to design efficient and resilient SD-WAN configurations.
Topic 3	SD-WAN Overlay Design and Best Practices: It focuses on the deployment of hub-and-spoke IPsec topologies and configuring ADVPN. Proficiency in this topic ensures that Fortinet network and security professionals can implement effective and reliable SD-WAN overlays tailored to organizational needs.
Topic 4	SD-WAN Troubleshooting: Troubleshooting SD-WAN issues, including rules, routing, and ADVPN, is vital for maintaining network reliability. This section of the Fortinet NSE 7 – SD-WAN 7.2 exam tests the ability to diagnose and resolve SD-WAN problems using diagnostic commands and monitoring tools, ensuring robust and uninterrupted network operations.
Topic 5	Centralized Management: This area focuses on deploying and managing SD-WAN through FortiManager, including using IPsec templates and SD-WAN Overlay Templates. Mastery here demonstrates the abilities of Fortinet network and security professionals to streamline SD-WAN configuration, enhance security, and maintain consistent policies across multiple sites.

Q55. Refer to the exhibit.

In a dual-hub hub-and-spoke SD-WAN deployment, which is a benefit of disabling the anti-replay setting on the hubs?

It instructs the hub to disable the reordering of TCP packets on behalf of the receiver, to improve performance.

It instructs the hub to disable TCP sequence number check, which is required for TCP sessions originated from spokes to fail over back and forth between the hubs.

It instructs the hub to not check the ESP sequence numbers on IPsec traffic, to improve performance.

It instructs the hub to skip content inspection on TCP traffic, to improve performance.

Q56. Refer to the exhibit.

In a dual-hub hub-and-spoke SD-WAN deployment, which is a benefit of disabling theanti-replaysetting on
the hubs?

It instructs the hub to disable the reordering of TCP packets on behalf of the receiver, to improve
performance.

It instructs the hub to disable TCP sequence number check, which is required for TCP sessions
originated from spokes to fail over back and forth between the hubs.

It instructs the hub to not check the ESP sequence numbers on IPsec traffic, to improve performance.

It instructs the hub to skip content inspection on TCP traffic, to improve performance.

Q57. Exhibit.

Which conclusion about the packet debug flow output is correct?

The total number of daily sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

The packet size exceeded the outgoing interface MTU.

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.

The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the firewall policy, and the packet was dropped.

Q58. Refer to the exhibit.

Which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules?

All traffic from a source IP to a destination IP is sent to the same interface.

All traffic from a source IP is sent to the same interface.

All traffic from a source IP is sent to the most used interface.

All traffic from a source IP to a destination IP is sent to the least used interface.

Q59. Refer to the exhibit.

Based on the exhibit, which two actions does FortiGate perform on sessions after a firewall policy change?
(Choose two.)

FortiGate flushes all sessions.

FortiGate terminates the old sessions.

FortiGate does not change existing sessions.

FortiGate evaluates new sessions.

Q60. Exhibit.

The exhibit shows the output of the command diagnose sys sdwan health-check status collected on a FortiGate device. Which two statements are correct about the health check status on this FortiGate device? (Choose two.)

The health-check VPN_PING orders the members according to the lowest jitter.

The interface T_INET_1 missed one SLA target.

There is no SLA criteria configured for the health-check Level3_DNS.

The interface T_INET_0 missed three SLA targets.

Q61. Refer to the exhibit.

Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2.
Which two configuration settings are required for Toronto and London spokes to establish an ADVPN shortcut? (Choose two.)

On the hubs, auto-discovery-sender must be enabled on the IPsec VPNs to spokes.

On the spokes, auto-discovery-receiver must be enabled on the IPsec VPN to the hub.

auto-discovery-forwarder must be enabled on all IPsec VPNs.

On the hubs, net-device must be enabled on all IPsec VPNs.

Q62. Refer to the exhibit.

Based on the exhibit, which action does FortiGate take?

FortiGate bounces port5 after it detects all SD-WAN members as dead.

FortiGate fails over to the secondary device after it detects all SD-WAN members as dead.

FortiGate brings up port5 after it detects all SD-WAN members as alive.

FortiGate brings down port5 after it detects all SD-WAN members as dead.

Q63. Refer to the exhibit, which shows an SD-WAN zone configuration on the FortiGate GUI.

Based on the exhibit, which statement is true?

You can delete the virtual-wan-link zone because it contains no member.

The corporate zone contains no member.

You can move port1 from the underlay zone to the overlay zone.

The overlay zone contains four members.

Q64. What is the route-tag setting in an SD-WAN rule used for?

To indicate the routes for health check probes.

To indicate the destination of a rule based on learned BGP prefixes.

To indicate the routes that can be used for routing SD-WAN traffic.

To indicate the members that can be used to route SD-WAN traffic.

Q65. Refer to the exhibit.

The exhibit shows the BGP configuration on the hub in a hub-and-spoke topology. The administrator wants BGP to advertise prefixes from spokes to other spokes over the IPsec overlays, including additional paths.
However, when looking at the spoke routing table, the administrator does not see the prefixes from other spokes and the additional paths.
Based on the exhibit, which three settings must the administrator configure inside each BGP neighbor group so spokes can learn other spokes prefixes and their additional paths? (Choose three.)

Set additional-path to send

Enable route-reflector-client

Set advertisement-interval to the number of additional paths to advertise

Set adv-additional-path to the number of additional paths to advertise

Enable soft-reconfiguration

Q66. Refer to the exhibit.

Which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules?

All traffic from a source IP to a destination IP is sent to the same interface.

All traffic from a source IP is sent to the same interface.

All traffic from a source IP is sent to the most used interface.

All traffic from a source IP to a destination IP is sent to the least used interface.

Q67. Refer to the exhibits.
Exhibit A

Exhibit B –

Exhibit A shows the configuration for an SD-WAN rule and exhibit B shows the respective rule status, the routing table, and the member status.
The administrator wants to understand the expected behavior for traffic matching the SD-WAN rule.
Based on the exhibits, what can the administrator expect for traffic matching the SD-WAN rule?

The traffic will be load balanced across all three overlays.

The traffic will be routed over T_INET_0_0.

The traffic will be routed over T_MPLS_0.

The traffic will be routed over T_INET_1_0.

Q68. Refer to the exhibit.

Based on the output, which two conclusions are true? (Choose two.)

There is more than one SD-WAN rule configured.

The SD-WAN rules take precedence over regular policy routes.

Theall_rulesrule represents the implicit SD-WAN rule.

Entry1(id=1)is a regular policy route.

Q69. The SD-WAN overlay template helps to prepare SD-WAN deployments. To complete the tasks performed by the SD-WAN overlay template, the administrator must perform some post-run tasks. What are three mandatory post-run tasks that must be performed? (Choose three.)

Create policy packages for branch devices.

Assign an sdwan_id metadata variable to each device (branch and hub}.

Configure routing through overlay tunnels created by the SD-WAN overlay template.

Assign a branch_id metadata variable to each branch device.

Configure SD-WAN rules.

Q70. Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?

When T_INET_0_0 and T_MPLS_0 have the same latency.

When T_MPLS_0 has a latency of 100 ms.

When T_INET_0_0 has a latency of 250 ms.

When T_N1PLS_0 has a latency of 80 ms.

Q71. Exhibit.

The exhibit shows VPN event logs on FortiGate. In the output shown in the exhibit, which statement is true?

There are no IPsec tunnel statistics log messages for ADVPN cuts.

There is one shortcut tunnel built from master tunnel T_MPLS_0.

The VPN tunnel T_MPLS_0 is a shortcut tunnel.

The master tunnel T_INET_0 cannot accept the ADVPN shortcut.

Q72. Refer to the exhibit.

Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to exchange routes over IPsec?

type must be set to static.

mode-cfg must be enabled.

exchange-interface-ip must be enabled.

add-route must be disabled.

Q73. What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process?
(Choose two.)

The FortiGate cloud key has not been added to the FortiGate cloud portal.

FortiDeploy has connected with FortiGate and provided the initial configuration to contact
FortiManager

The zero-touch provisioning process has completed internally, behind FortiGate.

FortiGate has obtained a configuration from the platform template in FortiGate cloud.

A factory reset performed on FortiGate.

Q74. Refer to the exhibit, which shows the IPsec phase 1 configuration of a spoke.

What must you configure on the IPsec phase 1 configuration for ADVPN to work with SD-WAN?

You must set ike-version to 1.

You must enable net-device.

You must enable auto-discovery-sender.

You must disable idle-timeout.

Q75. Refer to the exhibit.

Based on the exhibit, which two statements are correct about the health of the selected members? (Choose two.)

After FortiGate switches to active mode, FortiGate never fails back to passive monitoring.

During passive monitoring, FortiGate can’t detect dead members.

FortiGate can offload the traffic that is subject to passive monitoring to hardware.

FortiGate passively monitors the member if TCP traffic is passing through the member.

Q76. Refer to the exhibits.

Exhibit A shows the SD-WAN rule status and the learned BGP routes with community 65000:10.
Exhibit B shows the SD-WAN rule configuration, the BGP neighbor configuration, and the route map configuration.
The administrator wants to steer corporate traffic using routes tags in the SD-WAN rule ID 1.
However, the administrator observes that the corporate traffic does not match the SD-WAN rule ID 1.
Based on the exhibits, which configuration change is required to fix issue?

In the dcl-lab-rm route map configuration, set set-route-tag to 10.

In SD-WAN rule ID 1, change the destination to use ISDB entries.

In the BGP neighbor configuration, apply the route map dcl-lab-rm in the outbound direction.

In the dcl-lab-rm route map configuration, unset match-community.

Q77. Refer to the exhibit.

Which two statements about the IPsec VPN configuration and the status of the IPsec VPN tunnel are true?
(Choose two.)

FortiGate does not install IPsec static routes for remote protected networks in the routing table. Most Voted

The phase 1 configuration supports the network-overlay setting. Most Voted

FortiGate facilitated the negotiation of the T_INET_1_0_0 ADVPN shortcut over T_INET_1_0.

Dead peer detection is disabled.

Q78. Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows the SD-WAN performance SLA configuration, the SD-WAN rule configuration, and the application IDs of Facebook and YouTube. Exhibit B shows the firewall policy configuration and the underlay zone status.
Based on the exhibits, which two statements are correct about the health and performance of port1 and port2?
(Choose two.)