2025 Valid D-PE-OE-23 Exam Updates – 2025 Study Guide [Q14-Q30]

QUESTION 14
A server is equipped with 2 CPUs and 12x 8 GB DIMMs, for a total of 96 GB. The OS is not seeing all the memory.
Which memory mode should be configured so that all memory is seen by the OS?

QUESTION 15
A technician needs to connect a server to a network but the network switch has only two available network ports so only two network cables can be connected. The user needs as much bandwidth as possible for their workload so the two network cables need to connect to LOM1 and LOM2.
At some point in the future a new network switch will enable additional cables to be used. The technician wants to satisfy the user requirements yet still be able to access the iDRAC without having to reconfigure the iDRAC once new cables are installed in the iDRAC Dedicated NIC.
What is the best way to configure the iDRAC?

QUESTION 16
A technician is ready to deploy a server. If a critical part such as the system board fails, they must be able to replace the system board, reconfigure components, and update the firmware revisions in the fastest possible time.
How should the technician meet this requirement?

QUESTION 17
Eight new servers have arrived at a datacenter. All use static IP addresses for iDRAC. The technician needs to enable these servers to contact the DHCP server on the network to obtain new IP addresses.
What method can the technician use to quickly switch to DHCP?

QUESTION 18
A technician wants to remotely log in to a server but finds that the IDRAC virtual Console feature Is not available. Use the simulator to explore the system.
What Is the cause of this Issue? Note: It is necessary to dose (x) the simulator window before you can select a response to this question.

QUESTION 19
Which configuration settings are installed when using Easy Restore?

QUESTION 20
Before deploying a server, a customer needs a technician to configure the front panel LCD to display a custom message that contains the customer’s help desk phone number. However, the server cannot be rebooted.
Where can the technician configure the LCD?

QUESTION 21
A technician plugs in a server that has dual power supply units. After powering on the system, they notice that the power supply status indicators blink green then turn off.
What troubleshooting steps should the technician take to resolve this issue?

QUESTION 22
A customer encounters a MEM7114 message indicating the post package repair (PPR) has failed.
What should be the next step to reach a resolution?

QUESTION 23
What is the maximum number of local iDRAC users that can be created?

QUESTION 24
Under which heading can the user locate Lifecycle logs in the iDRAC Ul?

QUESTION 25
What is the recommended option to use when applying firmware to a replaced part using the Lifecycle Controller?

QUESTION 26
The OS and iDRAC report 120 GB of RAM. The technician has very little time to troubleshoot the issue and cannot run diagnostics.
They are working with the following information:
– Memory mode is Optimizer
– 8x 16 GB DIMMs installed
– 2 CPUs
– No entries in the SEL in the iDRAC
– No errors in the OS
To troubleshoot this issue, what action should the technician take prior to monitoring POST for any resulting errors?

QUESTION 27
In which Dell EMC PowerEdge server generation was the BOSS card introduced?

QUESTION 28
A technician is deploying a server.
What should they do once the server is fully configured and deployed?

QUESTION 29
A technician creates two virtual disks, Vdisk1 and Vdisk2, and assigns a dedicated hot spare for Vdisk1. A drive fails on Vdisk2.
What is the result?

QUESTION 30
An engineer needs to install an additional PSU on an existing, single PSU Dell EMC PowerEdge R740. They complete the initial installation and cabling procedures. They connect an AC cable and the power distribution unit produces normal AC output. The engineer checks power management and sees that the new PSU is in the Failed state.
What task should be completed to troubleshoot this issue?