BEST Verified Fortinet NSE4_FGT_AD-7.6 Exam Questions (2026) [Q46-Q61]

Rate this post

BEST Verified Fortinet NSE4_FGT_AD-7.6 Exam Questions (2026)

The Best Practice Test Preparation for the NSE4_FGT_AD-7.6 Certification Exam

Fortinet NSE4_FGT_AD-7.6 Exam Syllabus Topics:

Section	Objectives
Topic 1: VPN and Secure Connectivity	– IPsec VPN 1. Site-to-site VPN configuration 2. VPN troubleshooting – SSL VPN 1. Remote access configuration 2. User portal settings
Topic 2: Firewall Policies and Authentication	– Policy creation and management 1. Policy objects and services 2. IPv4/IPv6 policies – User authentication 1. Local users and groups 2. External authentication servers
Topic 3: Monitoring and Troubleshooting	– Diagnostics tools 1. Packet capture 2. Debug commands – Logging and reporting 1. FortiView monitoring 2. Event logs analysis
Topic 4: FortiGate Deployment and System Configuration	– Initial setup and configuration 1. Interface configuration 2. Administrative access – System maintenance 1. Backup and restore 2. Firmware upgrades
Topic 5: Routing and SD-WAN	– SD-WAN configuration 1. SD-WAN rules and health checks 2. Traffic steering – Static and dynamic routing 1. Policy-based routing 2. Route configuration
Topic 6: Security Profiles and Content Inspection	– Web filtering and application control 1. Policy enforcement 2. Profile configuration – Antivirus and intrusion prevention 1. Threat protection configuration 2. IPS signatures and policies
Topic 7: Network Security Concepts and Architecture	– Fortinet Security Fabric Overview 1. Integration across Fortinet products 2. Security architecture components

NEW QUESTION 46
Refer to the exhibit.

FortiGate is configured for firewall authentication. When attempting to access an external website, the user is not presented with a login prompt.
What is the most likely reason for this situation?

The Service DNS is required in the firewall policy.

The user is using an incorrect user name.

No matching user account exists for this user.

The Remote-users group is not added to the Destination.

NEW QUESTION 47
Refer to the exhibit showing a debug flow output.

Which two conclusions can you make from the debug flow output? (Choose two.)

The default gateway is configured on port2.

The RPF check fails.

The debug flow is for UDP traffic.

The matching firewall policy denies the traffic.

NEW QUESTION 48
Refer to the exhibit.

Based on the routing table shown in the exhibit, which two statements are true? (Choose two.)

A packet with the source IP address 10.0.13.10 arriving on port2 is allowed if strict RPF is disabled.

A packet with the source IP address 10.100.110.10 arriving on port2 is allowed if strict RPF is enabled.

A packet with the source IP address 10.100.110.10 arriving on port3 is allowed if strict RPF is disabled.

A packet with the source IP address 10.10.10.10 arriving on port2 is allowed if strict RPF is enabled.

NEW QUESTION 49
When configuring a FortiGate in a multi-WAN setup, why would an administrator enable session preservation on an interface? (Choose one answer)

To allow the FortiGate to dynamically change interfaces for all active sessions when a WAN link fails

To make sure all sessions without source NAT enabled always use the primary WAN link

To improve security by forcing users to authenticate again when the WAN link changes

To ensure that existing SSL VPN connections remain on the same interface even if route changes occur

NEW QUESTION 50
When configuring firewall policies which of the following is true regarding the policy ID? (Choose two.)

It is mandatory to provide a policy ID while creating a firewall policy regardless of GUI or CLI.

A firewall policy ID identifies the order of policy execution in firewall policies.

You can create a policy in CLI with policy ID 0.

A policy ID cannot be modified once a policy is created.

NEW QUESTION 51
Refer to the exhibit.

Based on the routing table shown in the exhibit, which two statements are true? (Choose two.)

A packet with the source IP address 10.0.13.10 arriving on port2 is allowed if strict RPF is disabled.

A packet with the source IP address 10.100.110.10 arriving on port2 is allowed if strict RPF is enabled.

A packet with the source IP address 10.100.110.10 arriving on port3 is allowed if strict RPF is disabled.

A packet with the source IP address 10.10.10.10 arriving on port2 is allowed if strict RPF is enabled.

NEW QUESTION 52
An administrator has configured the following settings.
config system settings
set ses-denied-traffic enable
end
config system global
set block-session-timer 30
end
What are the two results of this configuration? (Choose two.)

The number of logs generated by denied traffic is reduced.

A session for denied traffic is created.

Denied users are blocked for 30 minutes.

Session helpers are disabled for denied traffic.

NEW QUESTION 53
Refer to the exhibit. What would be the impact of these settings on the Server certificate SNI check configuration on FortiGate?

FortiGate will accept and use the CN in the server certificate for URL filtering if the SNI does not match the CN or SAN fields.

FortiGate will accept the connection with a warning if the SNI does not match the CN or SAN fields.

FortiGate will close the connection if the SNI does not match the CN or SAN fields.

FortiGate will close the connection if the SNI does not match the CN and SAN fields

NEW QUESTION 54
Refer to the exhibit. Why is the Antivirus scan switch grayed out when you are creating a new antivirus profile for FTP?

None of the inspected protocols are active in this profile.

FortiGate, with less than 2 GB RAM, does not support the Antivirus scan feature.

Antivirus scan is disabled under System -> Feature visibility.

The Feature Set for the profile is Flow-based but it must be Proxy-based.

NEW QUESTION 55
You have configured the below commands on a FortiGate.

What would be the impact of this configuration on FortiGate?

FortiGate will enable strict RPF on all its interfaces and porti will be exempted from RPF checks.

FortiGate will enable strict RPF on all its interfaces and porti will be enable for asymmetric routing.

The global configuration will take precedence and FortiGate will enable strict RPF on all interfaces.

Port1 will be enabled with flexible RPF. and all other interfaces will be enabled for strict RPF

NEW QUESTION 56
An administrator wants to ensure that a specific firewall policy on FortiGate is matched before any other policies for the same traffic. Which configuration change is most appropriate?

Enable central NAT

Increase the policy ID number

Move the policy higher in the policy list

Change the policy schedule to always

NEW QUESTION 57
Refer to the exhibits.

An administrator creates a new address object on the root FortiGate (Local-FortiGate) in the security fabric. After synchronization, this object is not available on the downstream FortiGate (ISFW).
What must the administrator do to synchronize the address object?

Change the csfsetting on both devices to set downstream-access enable.

Change the csfsetting on Local-FortiGate (root) to set fabric object-unification default.

Change the csfsetting on ISFW (downstream) to set authorization-request-type certificate.

Change the csfsetting on ISFW (downstream) to set configuration-sync local.

NEW QUESTION 58
What is the primary FortiGate election process when the HA override setting is enabled?

Connected monitored ports > Priority > HA uptime > FortiGate serial number

Connected monitored ports > Priority > System uptime > FortiGate serial number

Connected monitored ports > HA uptime > Priority > FortiGate serial number

Connected monitored ports > System uptime > Priority > FortiGate serial number

NEW QUESTION 59
Refer to the exhibit.

Based on the routing table shown in the exhibit, which two statements are true? (Choose two.)

A packet with the source IP address 10.0.13.10 arriving on port2 is allowed if strict RPF is disabled.

A packet with the source IP address 10.100.110.10 arriving on port2 is allowed if strict RPF is enabled.

A packet with the source IP address 10.100.110.10 arriving on port3 is allowed if strict RPF is disabled.

A packet with the source IP address 10.10.10.10 arriving on port2 is allowed if strict RPF is enabled.

NEW QUESTION 60
Refer to the exhibits. The exhibits show a diagram of a FortiGate device connected to the network, as well as the firewall policy and IP pool configuration on the FortiGate device.
Two PCs, PC1 and PC2, are connected behind FortiGate and can access the internet successfully. However, when the administrator adds a third PC to the network (PC3), the PC cannot connect to the internet.
Based on the information shown in the exhibit, which two configuration options can the administrator use to fix the connectivity issue for PC3? (Choose two.)